Multicast is the delivery of information to a group of destinations simultaneously, using the most efficient strategy to deliver messages over each link of the network only once, and create copies only when the links to the destinations split.
The word “multicast” is typically used to refer to IP Multicast, the implementation of the multicast concept on the IP routing level, where routers create optimal spanning tree distribution paths for data grams sent to a multicast destination address in realtime. However, there are also other implementations of the multicast distribution strategy listed below. (Source - wikipedia: http://en.wikipedia.org/wiki/Multicast).
GigaSpaces uses multicast in the following cases:
- When deploying to the service grid GigaSpaces XAP uses multicast to discover the Lookup Service, and register their proxies.
- Clients use multicast to discover the Lookup Service and look up a matching service proxy (such as the space).
Refer to the How to Determine Whether Multicast is Available section for more details.
To enable the important capabilities above, you should enable multicast on machines running clients, spaces or services.
- If you cannot enable multicast in your environment, you can use unicast discovery to allow services and clients to locate the Lookup Service.
- Space cluster replication uses unicast by default. You should use multicast replication when having more than 10 clients acting as replica spaces per target space.
In case you want to disable the Jini Lookup Service Multicast announcements please refer to this section in the Wiki.
To Multicast or to not Multicast?
Multicast is not a mandatory with XAP. It is used as a secondary mechanism for lookup service discovery. Unicast is the other mechanism. Both are turned on by default on the client side and on the service grid side (GSM,GSC,LUS).
Multicast is not used with replication , notification , monitoring or any client activity against the space. Disabling multicast discovery means you are loosing dynamicy for the lookup service location. This means if the lookup service fails (very low probably to happen) you will be able to start it only on the machines listed on the
LOOKUPLOCATORS list. Client
locators should have the same list used.
When multicast is disabled global lookup service should not be use. You should use only local lookup service configuration with the agent with the machines running the lookup service:
gs-agent gsa.global.lus 0 gsa.lus 1 gsa.gsm.global 0 gsa.gsm 1
Machines not running the lookup service should have their agent started using:
gs-agent gsa.global.lus 0 gsa.lus 0 gsa.gsm.global 0 gsa.gsm 0
The GSC count should be added to the commands above above as usual.
If you can’t have multicast enabled within your network you should disable it on the client side and on the service grid side. It will save some CPU activity performed continuously.
Configuring Multicast on Linux
In some cases, Linux distributions do not have multicast enabled by default and the
/etc/hosts file does not include the IP address associated with the server’s hostname. An error that is frequently met is:
hostname associated with the localhost in
/etc/hosts. The machine’s hostname in
/etc/hosts should be associated with the IP address set to the server’s network interface, or to the external static NAT IP address of the server (the address clients should connect to).
Make sure the
/etc/hosts has the machine’s IP, together with the IP:
127.0.0.1 localhost 192.168.10.127 Mylinux
Make sure all network machines can ping each other. You might need to list all the network machines’ IPs as part of each machine’s
hosts file, or have a DHCP server configured.
Before running GigaSpaces, make sure your network interface supports multicast, and the appropriate routes are properly configured.
To check if your network interface supports multicast, run the following
$ /sbin/ifconfig -a eth0 Link encap:Ethernet HWaddr 00:30:48:2E:67:BA inet addr:192.168.10.127 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe2e:67ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:89049707 errors:34 dropped:0 overruns:0 frame:34 TX packets:79402911 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:24029278032 (22.3 GiB) TX bytes:52438225932 (48.8 GiB) Base address:0x3000 Memory:dc300000-dc320000 eth1 Link encap:Ethernet HWaddr 00:30:48:2E:67:BB inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe2e:67bb/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Base address:0x3040 Memory:dc320000-dc340000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1366770822 errors:0 dropped:0 overruns:0 frame:0 TX packets:1366770822 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:319301580062 (297.3 GiB) TX bytes:319301580062 (297.3 GiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
MULTICAST attribute in the fourth line of the
eth0 properties is not present, it’s possible that your kernel has not been compiled with multicast support. Before re-compiling the kernel, try enabling multicast on your network interface (
eth0 in this case) via
$ /sbin/ifconfig etho multicast
To check that multicast routing is configured, run the following
$ /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 220.127.116.11 0.0.0.0 240.0.0.0 U 0 0 0 eth0 0.0.0.0 192.168.10.1 0.0.0.0 UG 0 0 0 eth0
If the destination
18.104.22.168 entry is not present, you need to enable multicast routing.
To enable multicast routing, run the following
route command as root:
$ /sbin/route -n add -net 22.214.171.124 netmask 240.0.0.0 dev eth0
On Redhat systems you can configure this route statically via the network setup configuration tools – see: redhat - Chapter 6. Network Configuration.
Alternatively, try executing the command above as part of a startup script in
For more details on Linux
route commands, refer to:
tcpdump is another useful command which dumps traffic on a network:
tcpdump -i eth0 ip multicast
By default multicast is not allowed between the virtual machines, so the unicast should be configured instead
Configuring Multicast on Windows
To enable multicasting from a token ring on a Windows® 2000 workstation to any Windows 98/NT machine, set the
TrFunctionalMcastAddress parameter to
0 in the Windows 2000 registry:
- Click Start* > *Run on the Windows 2000 taskbar.
- In the Open field, select or type REGEDIT.
- Click OK. The Registry Editor window opens.
- Click HKEY_LOCAL_Machine > SYSTEM > CurrentControlSet > Services > Tcpip > Parameters.
- Right-click TrFunctionalMcastAddress, and click Modify. The Edit DWORD Value window opens.
- In the Value data field, type
- Click OK to save changes and exit.
- Close the Registry Editor.
Configuring Multicast Scope Time-To-Live (TTL) Value
The multicast Time-To-Live (TTL) value specifies the number of routers (hops) that multicast traffic is permitted to pass through before expiring on the network. For each router (hop), the original specified TTL is decremented by one (1). When its TTL reaches a value of zero (0), each multicast datagram expires and is no longer forwarded through the network to other subnets.
The problem of multicasts/broadcasts not passing the router/switch is a well known issue - most routers (Cisco, 3Com, etc) have multicast forwarding disabled by default - otherwise the networks will be flooded with packets coming from very distant locations. To get it delivered all over the globe takes below 30 hops, so TTL 20 means delivery to more than half of it. It is very common that network experts in large networks hate the flooding problem caused by multicasts/broadcasts sent with the large TTL, and block it.
Packet Sniffer/Network Analyzer Tool
Wireshark (formerly Ethereal) - accumulates years of network analyzing experience and is far more mature and known than other tools. It is a cross-platform packet sniffer/network analyzer tool (used both in Windows and Unix/Linux). It allows you to examine data from a live network, or from a capture file on disk. You can interactively browse the capture data, viewing summary and detail information for each packet. It has several powerful features, including a rich display filter language and the ability to view the reconstructed stream of a TCP session.
To find TTL, you should monitor some traffic (start-stop on the proper interface), in the monitoring log. Choose the packet you are interested in, and look at its IP layer - TTL (and other parameters) are shown.
The default TTL value is 3 (was 15). See Multicast Settings section for details of how to modify that value.